Dimail Mining Parts

Author: ueslk_admin

  • Sliding Piece 3128303930 for use with EPIROC®: Fitment, Wear and Stocking Guide

    Part number 3128303930 is unusual among wear pads: it is not tied to a single rig family. The same sliding piece serves Boomer™ underground jumbos, Boltec™ bolting rigs and Roc™ / FlexiROC™ surface rigs — which makes it one of the most useful numbers to know if your fleet is not made up of identical machines.

    This guide covers which machines use it, why one number spans so many models, how it relates to its sister pad 3128307488, what wear looks like in daily inspection, and how to stock it across a mixed fleet without over-ordering.

    What 3128303930 Is, and Which Machines Use It

    3128303930 is a cross-referenced aftermarket sliding piece (also called a slide piece, wear pad or wear slide) for the feed beam of EPIROC® drill rigs. It is a sacrificial polymer pad that runs between the feed beam rail and the sliding carrier.

    The number is referenced against a wide fitment list, including:

    • Boomer™ 104, 281, 282 and XL3 — underground development and production jumbos
    • Boltec™ 235 and 235H — underground rock bolting rigs
    • Roc™ D55 and D65 — surface crawler rigs for quarry and construction drilling
    • FlexiROC™ D60 — surface rigs for quarries, mines and civil works

    Two practical notes before ordering:

    • Confirm by the number on the old part, then by serial. Fitment lists are a starting point; feed beam revisions can change pad dimensions or layout. Your machine’s spare parts manual, checked against your serial number, is the final word.
    • Measure the worn pad before you buy. The new pad’s thickness must match the manual specification, not whatever thickness is left on the worn one.

    Why One Number Covers So Many Rigs

    It looks strange that a pad on an underground bolting rig and a surface crawler wears the same number. The explanation is standardisation: EPIROC® feed beams across several product lines share the same rail profile and carrier interface, so the same polymer pad fits all of them.

    For buyers, this has three consequences:

    1. One stock line covers many machines. A fleet of Boomers, a Boltec and a Roc D65 can share a single 3128303930 stock position instead of three.
    2. Ordering errors are easier to catch. If a supplier claims the pad fits your rig, the cross-machine fitment is easy to verify — the same pad is already running on other models in your fleet.
    3. Demand is steadier. A part used across several rig types moves more predictably than a single-model item, which is why it is a sensible first item to hold in stock.

    What It Does on the Machine

    Functionally the pad does four jobs at once: it guides the carrier and holds drilling alignment, it spreads feed and clamping loads over the rail, it acts as the sacrificial surface so the steel rail does not wear, and it damps shock while limiting rock dust in the sliding interface.

    We cover the physics in detail in our 3128307488 slide piece guide — the wear mechanism is the same, so this article stays focused on fitment and stocking.

    The Mixed-Fleet Reality: 3128303930 and 3128307488

    If your workshop runs both numbers, you are not imagining it. A single feed beam can carry pads in more than one position, and different beam revisions use different pads on otherwise similar machines. In practice:

    • 3128303930 is the broad-coverage pad described in this article — one number across Boomer™, Boltec™, Roc™ and FlexiROC™ models.
    • 3128307488 is its sister pad, used on Boomer™ 281 / 282 and FlexiROC™ class feed beams at other positions or on other beam revisions.

    The safe rule has not changed: order by the number moulded or stamped on the pad you are replacing. If the number is worn away, send us a photo with dimensions and your rig model and serial — we will confirm which pad you need before you pay.

    Both numbers are covered on our Sliding Pieces & Wear Pads category page, with a machine-to-part compatibility matrix.

    Wear Signs Worth Acting On

    The inspection routine is the same as for any feed beam pad, and it takes about five minutes per shift:

    • Thickness below the wear limit — check against the manual or against a new pad; a fingernail-catch step across the face means uneven wear has started.
    • Shiny metal contact marks on the rail — the clearest signal that the pad has stopped separating steel from steel. Stop and replace.
    • Cracks, chips or embedded rock dust — embedded grit turns the pad into sandpaper for the rail.
    • Uneven wear at one end — points to rail misalignment; new pads alone will not fix it.
    • Rising feed pressure or slower penetration — increasing friction in the sliding interface often shows up here first.
    • Collaring drift — play in the sliding interface appears first as inaccurate hole starts.

    Choosing a Replacement Pad

    For an aftermarket 3128303930, compare suppliers on the same points we use ourselves:

    • Fitment validation — dimensions cross-checked against the fitment list and real beams, not just a number match.
    • Polymer grade — a named material with stable dimensions under heat, load and hydraulic oil exposure.
    • Thickness tolerance — clearance in the feed system lives in fractions of a millimetre.
    • Flatness and surface finish — the running face decides how the rail wears.
    • Batch consistency — the tenth set should feel identical to the first.

    A pad that is slightly thin or slightly off in profile will fit loosely, wear quickly and pass the blame to your rails. If a supplier cannot state the material grade or the tolerance, that tells you enough.

    Stocking Strategy for a Mixed Fleet

    Because 3128303930 spans several rig types, it is the natural first item in a wear-pad stock position:

    1. Count the consumers. Every rig on the fitment list that runs 3128303930 pads, times pads per beam, gives your consumption base.
    2. Set a min-max. Track average pad life per machine class, then hold a minimum that covers one full change-out on your most pad-hungry rig plus a safety margin for delivery time.
    3. Reorder on consumption, not on failure. Pads removed at the wear limit during planned maintenance cost nothing extra; pads that fail mid-shift cost downtime.
    4. Keep one spare set per beam position on the shelf, and let the supplier hold the rest — with a ex-stock dispatch partner, shelf space beats inventory.

    Installation Notes

    • Clean the rail and carrier seats before fitting; grit trapped under a new pad becomes immediate rail wear.
    • Check fastener torque to the manual specification — an undertorqued pad moves, an overtightened one creeps.
    • Confirm the carrier slides freely by hand through a full stroke before returning the rig to service.
    • Re-check after the first shift: early seating wear is normal, movement is not.

    Ordering Checklist

    1. The number on the worn pad (or a photo with dimensions if it is illegible).
    2. Rig model and serial number.
    3. Quantity.
    4. Delivery country and port, for an accurate shipped quote.

    Send these four items to dimailmachinery@126.com and you will have a quotation within 12 working hours; stock items are dispatched promptly after order confirmation.

    Frequently Asked Questions

    Is 3128303930 really the same pad on a Boltec™ and a Roc™ D65?

    Yes — the feed beam interface those machines share uses the same pad. Beam revisions can still vary, so the number on the old part and the serial number remain the deciding check before any order.

    Can I use 3128307488 instead if 3128303930 is out of stock?

    No. The two pads differ in dimensions. Substituting one for the other produces loose fit, fast wear and rail damage. Order the number on the pad you removed.

    How long should a sliding piece last?

    It depends on rock abrasiveness, feed force and hours. Pads are consumables measured in weeks or months of operation, which is exactly why they belong on planned maintenance intervals rather than run-to-failure.

    Do you supply other wear parts for the same machines?

    Yes. We supply a range of aftermarket parts for use with EPIROC® and Atlas Copco® equipment, and we quote full wear-parts lists as a single shipment. Send the list and we will mark what we stock.

    Sourcing 3128303930

    Dimail supplies the 3128303930 sliding piece as an aftermarket spare part for use with EPIROC® drill rigs — MOQ one piece, dispatched from stock, quoted within 12 working hours. Full details, photos and the inquiry form are on the 3128303930 product page; the parts catalog lists all part numbers we currently cover.

    EPIROC®, ATLAS COPCO®, Boomer™, Boltec™, Roc™ and FlexiROC™ are trademarks of Epiroc AB and Atlas Copco AB. Dimail is not affiliated with or endorsed by either company; part numbers are used for cross-reference only.

  • Slide Piece 3128307488 for use with EPIROC®: When to Replace, How to Choose

    Part number 3128307488 is one of the cheapest items on an EPIROC® Boomer™ or FlexiROC™ rig — and one of the few that can quietly cost you a feed beam. It is the slide piece (also called a wear pad, wear strip or sliding pad) that sits between the feed beam rails and the carrier, and it is replaced far more often than it is understood.

    This article covers what the pad actually does on the machine, why running it past its wear limit is a false economy, how to read the early warning signs, and — most importantly — how to choose a replacement pad that performs like the original instead of one that eats rails.

    What 3128307488 Is, and Where It Sits

    3128307488 is a cross-referenced aftermarket slide piece for the feed beam of EPIROC® Boomer™ and FlexiROC™ class drill rigs. On the machine it is a sacrificial polymer pad clamped between the steel rail of the feed beam and the sliding carrier that pushes the rock drill forward.

    Every feed cycle — collaring, drilling, retracting, rod handling — slides the carrier along these pads under load. Nothing else in the feed system takes that combination of continuous sliding, abrasive rock dust and clamping force.

    Two practical notes before you order anything:

    • Confirm by machine serial, not by number alone. Feed beams vary by model and revision, and the same beam can use pads in more than one thickness or position. Your machine’s spare parts manual lists the exact quantity and position for your serial number.
    • Measure before you buy. A worn pad’s remaining thickness tells you how far it has gone; the new pad’s thickness must match the manual, not the worn part.

    Four Jobs the Slide Piece Does on the Whole Machine

    It looks like a simple plastic block. Functionally it is a precision element of the feed system, and it carries four jobs at once.

    1. It guides the carrier and holds alignment

    The pad sets the clearance between carrier and rail. That clearance decides whether the drill runs straight. Once the pad wears thin, the carrier gains play, and play turns into drift at collaring, hole deviation and a drilling pattern that no longer matches the plan.

    2. It spreads feed and clamping loads

    Feed force and rail clamping pressure are concentrated on a small contact area. The pad distributes that load so the rail sees a broad, even surface instead of a point load. Thin or warped pads turn the load into local stress — the beginning of rail wear, cracking and distortion.

    3. It protects the rail — it is the part designed to die

    The pad is deliberately the sacrificial element. Polymer is cheap and replaceable in minutes; a scored or distorted feed beam is a machining or replacement job that takes the rig out of production. Every hour a worn pad is left in place, the rail is doing the wearing instead.

    4. It damps shock and limits contamination

    Impact loads from drilling travel back through the carrier. The pad absorbs part of that shock before it reaches the beam structure, and its contact face helps wipe the rail, limiting how much abrasive dust works its way into the sliding interface.

    Why Replacing It Is Not Optional

    Wear pads fail slowly, which is exactly why they get ignored. The sequence is predictable:

    1. Clearance grows. The carrier starts to feel loose. Penetration rate drops slightly and nobody notices.
    2. Steel meets steel. The pad wears through or cracks, and the carrier begins running on the rail. Rails score, then gall.
    3. Everything gets more expensive. Feed pressure rises, drilling accuracy falls, vibration increases — and the rig either starts making bad holes or stops making holes at all.
    4. The failure happens at the worst moment. A pad that let go underground, mid-shift, costs far more in downtime, crane time and lost metres than a set of pads ever will.

    There is also a safety dimension: a worn or loose pad allows the carrier to move under load in ways the feed system was not designed for. That is a structural and personnel risk, not just a productivity one.

    The economics are simple. A slide piece is a low-cost consumable that takes minutes to change. A feed beam is a machined structural component. Treating the first as optional is how you end up paying for the second.

    Six Signs the Pad Is Done

    • Thickness below the wear limit. Compare against the minimum in the manual, or against a new pad. A step you can feel with a fingernail across the pad face means it is already uneven.
    • Shiny metal contact marks on the rail. This is the clearest warning: the pad is no longer separating steel from steel. Stop running and replace.
    • Cracks, chips or embedded rock dust. Once abrasive material is embedded in the polymer, it acts like sandpaper on the rail.
    • Uneven wear along the pad. Heavier wear at one end points to rail misalignment or a beam problem — new pads alone will not fix it.
    • Higher feed pressure, slower penetration. A rising feed pressure trend at constant rock conditions usually traces back to friction, not to the rock drill.
    • Carrier wander or drift when collaring. Play in the sliding interface shows up first as inaccurate collaring.

    A five-minute check each shift — visual pass, feel for a wear step, look for metal contact marks — catches all of this long before it becomes downtime.

    How to Choose Wear Pads: Eight Checks

    This is where most buyers go wrong. “Same part number, cheaper price” is not a specification. Compare suppliers on these eight points.

    1. The cross-reference, not just the number

    Ask how the supplier validates fitment: by machine model and serial range, by measured dimensions, or by nothing more than a number match. A pad that is 1 mm thin or has hole spacing slightly off will fit loosely, wear fast, and pass the blame to your rails.

    2. The polymer specification

    Request the material datasheet: base polymer, grade, filler content, wear rate and water absorption. Two pads can look identical and behave completely differently — one keeps its dimensions under heat and load, the other creeps and flattens within weeks. If a supplier cannot name the material grade, that is your answer.

    3. Dimensional tolerance

    Ask for the thickness tolerance and hole position tolerance. Clearance in the feed system is defined in fractions of a millimetre; a batch that drifts across the tolerance band will give you inconsistent machine feel from one set to the next.

    4. Flatness and surface finish

    A warped pad contacts the rail on its high spots only. That creates point loading, rapid local wear and premature failure — even if the material itself is correct.

    5. Batch consistency

    Consistency matters more than a single good sample. Ask whether dimensions are checked per batch and whether a certificate or inspection record ships with the order. Mixed batches are the most common cause of uneven wear on one rail versus the other.

    6. Temperature and oil resistance

    Feed beams get hot, hydraulic oil gets everywhere, and washing chemicals are common in workshops. Confirm the material holds its hardness and dimensions in that environment — not just at room temperature on a datasheet.

    7. Whether they can machine to your drawing

    If your beam revision uses a different thickness, or you want a wear pad for another position on the same rig, a supplier who can cut to drawing saves you a second sourcing exercise.

    8. Supply and lead time

    A wear part is only useful if the next set arrives before the current one dies. Look for a low minimum order — one piece for a trial — short dispatch time, and evidence that repeat orders come from the same specification.

    Cheap Pad vs. Correct Pad: What the Difference Costs

    • Wrong material, right shape: wears two to three times faster, so you buy it repeatedly — and each change is a production stop.
    • Wrong thickness: play in the carrier, poor collaring accuracy, and a rig that “feels loose” no matter what you adjust.
    • Warped or inconsistent batch: uneven wear, rail scoring, and eventually rail work that costs many times the pad price.
    • Correct pad, poor supply: you run the old one past its limit because the replacement is three weeks out. That is how rails get destroyed.

    The right way to compare is cost per metre drilled, not price per piece. A pad that lasts twice as long at 40 percent more cost is the cheaper part.

    Installation and Break-In

    1. Clean the rail completely. Remove swarf, burrs and compacted dust. A pad clamped over debris sits unevenly from day one.
    2. Fit as a set per rail. Do not mix a new pad with a worn one on the same rail — the load distribution will be wrong and the new pad will wear fast.
    3. Torque to the manual. Under-tightening allows movement; over-tightening distorts the pad.
    4. Run a break-in period. For the first shifts, keep feed force moderate and re-check clearance afterwards.
    5. Log the change. Metres drilled and calendar time per set gives you a replacement interval based on your own rock conditions instead of guesswork.

    Ordering Checklist

    • Machine model, serial number and feed beam revision
    • Position on the beam and quantity needed per beam
    • Pad thickness required (from the manual, not the worn part)
    • Material grade or datasheet required by your maintenance standard
    • One trial set before a bulk order

    Frequently Asked Questions

    Is 3128307488 the same on every Boomer™ and FlexiROC™ feed beam?

    No. The number cross-references a family of slide pieces, and beams differ by model and revision in thickness and position. Always confirm against your machine’s spare parts manual using the serial number.

    How long should a slide piece last?

    It depends heavily on rock abrasiveness, feed force and how well the rails are maintained. Highly abrasive ground can consume a pad in weeks; softer conditions and good alignment stretch it to months. Logging your own change intervals is the only reliable answer.

    Can I replace only the worn pad?

    Replace all pads on the same rail together. A mixed set changes load distribution, accelerates wear on the new part and can affect carrier alignment.

    Do I need to check anything else when the pads are worn?

    Yes — inspect the rails for scoring and check alignment. Uneven pad wear is usually a symptom of a beam or rail problem rather than a pad quality problem.

    Sourcing 3128307488

    Dimail supplies the aftermarket slide piece for EPIROC® 3128307488 as a direct cross-reference replacement: dimension-checked per batch, dispatched from stock, minimum order one piece so you can run a trial set on your own rig first. The full wear-part range is indexed in the aftermarket parts catalog.

    If you are still deciding which parts to keep in stock, start with the Boomer™ and FlexiROC™ wear parts guide — it covers the consumables that fail first and a shift-level inspection routine.

    EPIROC®, ATLAS COPCO®, Boomer™ and FlexiROC™ are trademarks of Epiroc AB and Atlas Copco AB. Dimail is not affiliated with or endorsed by either company; part numbers are used for cross-reference only.