Part number 3128307488 is one of the cheapest items on an EPIROC® Boomer™ or FlexiROC™ rig — and one of the few that can quietly cost you a feed beam. It is the slide piece (also called a wear pad, wear strip or sliding pad) that sits between the feed beam rails and the carrier, and it is replaced far more often than it is understood.
This article covers what the pad actually does on the machine, why running it past its wear limit is a false economy, how to read the early warning signs, and — most importantly — how to choose a replacement pad that performs like the original instead of one that eats rails.
What 3128307488 Is, and Where It Sits
3128307488 is a cross-referenced aftermarket slide piece for the feed beam of EPIROC® Boomer™ and FlexiROC™ class drill rigs. On the machine it is a sacrificial polymer pad clamped between the steel rail of the feed beam and the sliding carrier that pushes the rock drill forward.
Every feed cycle — collaring, drilling, retracting, rod handling — slides the carrier along these pads under load. Nothing else in the feed system takes that combination of continuous sliding, abrasive rock dust and clamping force.
Two practical notes before you order anything:
- Confirm by machine serial, not by number alone. Feed beams vary by model and revision, and the same beam can use pads in more than one thickness or position. Your machine’s spare parts manual lists the exact quantity and position for your serial number.
- Measure before you buy. A worn pad’s remaining thickness tells you how far it has gone; the new pad’s thickness must match the manual, not the worn part.
Four Jobs the Slide Piece Does on the Whole Machine
It looks like a simple plastic block. Functionally it is a precision element of the feed system, and it carries four jobs at once.
1. It guides the carrier and holds alignment
The pad sets the clearance between carrier and rail. That clearance decides whether the drill runs straight. Once the pad wears thin, the carrier gains play, and play turns into drift at collaring, hole deviation and a drilling pattern that no longer matches the plan.
2. It spreads feed and clamping loads
Feed force and rail clamping pressure are concentrated on a small contact area. The pad distributes that load so the rail sees a broad, even surface instead of a point load. Thin or warped pads turn the load into local stress — the beginning of rail wear, cracking and distortion.
3. It protects the rail — it is the part designed to die
The pad is deliberately the sacrificial element. Polymer is cheap and replaceable in minutes; a scored or distorted feed beam is a machining or replacement job that takes the rig out of production. Every hour a worn pad is left in place, the rail is doing the wearing instead.
4. It damps shock and limits contamination
Impact loads from drilling travel back through the carrier. The pad absorbs part of that shock before it reaches the beam structure, and its contact face helps wipe the rail, limiting how much abrasive dust works its way into the sliding interface.
Why Replacing It Is Not Optional
Wear pads fail slowly, which is exactly why they get ignored. The sequence is predictable:
- Clearance grows. The carrier starts to feel loose. Penetration rate drops slightly and nobody notices.
- Steel meets steel. The pad wears through or cracks, and the carrier begins running on the rail. Rails score, then gall.
- Everything gets more expensive. Feed pressure rises, drilling accuracy falls, vibration increases — and the rig either starts making bad holes or stops making holes at all.
- The failure happens at the worst moment. A pad that let go underground, mid-shift, costs far more in downtime, crane time and lost metres than a set of pads ever will.
There is also a safety dimension: a worn or loose pad allows the carrier to move under load in ways the feed system was not designed for. That is a structural and personnel risk, not just a productivity one.
The economics are simple. A slide piece is a low-cost consumable that takes minutes to change. A feed beam is a machined structural component. Treating the first as optional is how you end up paying for the second.
Six Signs the Pad Is Done
- Thickness below the wear limit. Compare against the minimum in the manual, or against a new pad. A step you can feel with a fingernail across the pad face means it is already uneven.
- Shiny metal contact marks on the rail. This is the clearest warning: the pad is no longer separating steel from steel. Stop running and replace.
- Cracks, chips or embedded rock dust. Once abrasive material is embedded in the polymer, it acts like sandpaper on the rail.
- Uneven wear along the pad. Heavier wear at one end points to rail misalignment or a beam problem — new pads alone will not fix it.
- Higher feed pressure, slower penetration. A rising feed pressure trend at constant rock conditions usually traces back to friction, not to the rock drill.
- Carrier wander or drift when collaring. Play in the sliding interface shows up first as inaccurate collaring.
A five-minute check each shift — visual pass, feel for a wear step, look for metal contact marks — catches all of this long before it becomes downtime.
How to Choose Wear Pads: Eight Checks
This is where most buyers go wrong. “Same part number, cheaper price” is not a specification. Compare suppliers on these eight points.
1. The cross-reference, not just the number
Ask how the supplier validates fitment: by machine model and serial range, by measured dimensions, or by nothing more than a number match. A pad that is 1 mm thin or has hole spacing slightly off will fit loosely, wear fast, and pass the blame to your rails.
2. The polymer specification
Request the material datasheet: base polymer, grade, filler content, wear rate and water absorption. Two pads can look identical and behave completely differently — one keeps its dimensions under heat and load, the other creeps and flattens within weeks. If a supplier cannot name the material grade, that is your answer.
3. Dimensional tolerance
Ask for the thickness tolerance and hole position tolerance. Clearance in the feed system is defined in fractions of a millimetre; a batch that drifts across the tolerance band will give you inconsistent machine feel from one set to the next.
4. Flatness and surface finish
A warped pad contacts the rail on its high spots only. That creates point loading, rapid local wear and premature failure — even if the material itself is correct.
5. Batch consistency
Consistency matters more than a single good sample. Ask whether dimensions are checked per batch and whether a certificate or inspection record ships with the order. Mixed batches are the most common cause of uneven wear on one rail versus the other.
6. Temperature and oil resistance
Feed beams get hot, hydraulic oil gets everywhere, and washing chemicals are common in workshops. Confirm the material holds its hardness and dimensions in that environment — not just at room temperature on a datasheet.
7. Whether they can machine to your drawing
If your beam revision uses a different thickness, or you want a wear pad for another position on the same rig, a supplier who can cut to drawing saves you a second sourcing exercise.
8. Supply and lead time
A wear part is only useful if the next set arrives before the current one dies. Look for a low minimum order — one piece for a trial — short dispatch time, and evidence that repeat orders come from the same specification.
Cheap Pad vs. Correct Pad: What the Difference Costs
- Wrong material, right shape: wears two to three times faster, so you buy it repeatedly — and each change is a production stop.
- Wrong thickness: play in the carrier, poor collaring accuracy, and a rig that “feels loose” no matter what you adjust.
- Warped or inconsistent batch: uneven wear, rail scoring, and eventually rail work that costs many times the pad price.
- Correct pad, poor supply: you run the old one past its limit because the replacement is three weeks out. That is how rails get destroyed.
The right way to compare is cost per metre drilled, not price per piece. A pad that lasts twice as long at 40 percent more cost is the cheaper part.
Installation and Break-In
- Clean the rail completely. Remove swarf, burrs and compacted dust. A pad clamped over debris sits unevenly from day one.
- Fit as a set per rail. Do not mix a new pad with a worn one on the same rail — the load distribution will be wrong and the new pad will wear fast.
- Torque to the manual. Under-tightening allows movement; over-tightening distorts the pad.
- Run a break-in period. For the first shifts, keep feed force moderate and re-check clearance afterwards.
- Log the change. Metres drilled and calendar time per set gives you a replacement interval based on your own rock conditions instead of guesswork.
Ordering Checklist
- Machine model, serial number and feed beam revision
- Position on the beam and quantity needed per beam
- Pad thickness required (from the manual, not the worn part)
- Material grade or datasheet required by your maintenance standard
- One trial set before a bulk order
Frequently Asked Questions
Is 3128307488 the same on every Boomer™ and FlexiROC™ feed beam?
No. The number cross-references a family of slide pieces, and beams differ by model and revision in thickness and position. Always confirm against your machine’s spare parts manual using the serial number.
How long should a slide piece last?
It depends heavily on rock abrasiveness, feed force and how well the rails are maintained. Highly abrasive ground can consume a pad in weeks; softer conditions and good alignment stretch it to months. Logging your own change intervals is the only reliable answer.
Can I replace only the worn pad?
Replace all pads on the same rail together. A mixed set changes load distribution, accelerates wear on the new part and can affect carrier alignment.
Do I need to check anything else when the pads are worn?
Yes — inspect the rails for scoring and check alignment. Uneven pad wear is usually a symptom of a beam or rail problem rather than a pad quality problem.
Sourcing 3128307488
Dimail supplies the aftermarket slide piece for EPIROC® 3128307488 as a direct cross-reference replacement: dimension-checked per batch, dispatched from stock, minimum order one piece so you can run a trial set on your own rig first. The full wear-part range is indexed in the aftermarket parts catalog.
If you are still deciding which parts to keep in stock, start with the Boomer™ and FlexiROC™ wear parts guide — it covers the consumables that fail first and a shift-level inspection routine.
EPIROC®, ATLAS COPCO®, Boomer™ and FlexiROC™ are trademarks of Epiroc AB and Atlas Copco AB. Dimail is not affiliated with or endorsed by either company; part numbers are used for cross-reference only.
Leave a Reply