Dimail Mining Parts

Sliding Piece 3128303930 for use with EPIROC®: Fitment, Wear and Stocking Guide

Written by

in

Part number 3128303930 is unusual among wear pads: it is not tied to a single rig family. The same sliding piece serves Boomer™ underground jumbos, Boltec™ bolting rigs and Roc™ / FlexiROC™ surface rigs — which makes it one of the most useful numbers to know if your fleet is not made up of identical machines.

This guide covers which machines use it, why one number spans so many models, how it relates to its sister pad 3128307488, what wear looks like in daily inspection, and how to stock it across a mixed fleet without over-ordering.

What 3128303930 Is, and Which Machines Use It

3128303930 is a cross-referenced aftermarket sliding piece (also called a slide piece, wear pad or wear slide) for the feed beam of EPIROC® drill rigs. It is a sacrificial polymer pad that runs between the feed beam rail and the sliding carrier.

The number is referenced against a wide fitment list, including:

  • Boomer™ 104, 281, 282 and XL3 — underground development and production jumbos
  • Boltec™ 235 and 235H — underground rock bolting rigs
  • Roc™ D55 and D65 — surface crawler rigs for quarry and construction drilling
  • FlexiROC™ D60 — surface rigs for quarries, mines and civil works

Two practical notes before ordering:

  • Confirm by the number on the old part, then by serial. Fitment lists are a starting point; feed beam revisions can change pad dimensions or layout. Your machine’s spare parts manual, checked against your serial number, is the final word.
  • Measure the worn pad before you buy. The new pad’s thickness must match the manual specification, not whatever thickness is left on the worn one.

Why One Number Covers So Many Rigs

It looks strange that a pad on an underground bolting rig and a surface crawler wears the same number. The explanation is standardisation: EPIROC® feed beams across several product lines share the same rail profile and carrier interface, so the same polymer pad fits all of them.

For buyers, this has three consequences:

  1. One stock line covers many machines. A fleet of Boomers, a Boltec and a Roc D65 can share a single 3128303930 stock position instead of three.
  2. Ordering errors are easier to catch. If a supplier claims the pad fits your rig, the cross-machine fitment is easy to verify — the same pad is already running on other models in your fleet.
  3. Demand is steadier. A part used across several rig types moves more predictably than a single-model item, which is why it is a sensible first item to hold in stock.

What It Does on the Machine

Functionally the pad does four jobs at once: it guides the carrier and holds drilling alignment, it spreads feed and clamping loads over the rail, it acts as the sacrificial surface so the steel rail does not wear, and it damps shock while limiting rock dust in the sliding interface.

We cover the physics in detail in our 3128307488 slide piece guide — the wear mechanism is the same, so this article stays focused on fitment and stocking.

The Mixed-Fleet Reality: 3128303930 and 3128307488

If your workshop runs both numbers, you are not imagining it. A single feed beam can carry pads in more than one position, and different beam revisions use different pads on otherwise similar machines. In practice:

  • 3128303930 is the broad-coverage pad described in this article — one number across Boomer™, Boltec™, Roc™ and FlexiROC™ models.
  • 3128307488 is its sister pad, used on Boomer™ 281 / 282 and FlexiROC™ class feed beams at other positions or on other beam revisions.

The safe rule has not changed: order by the number moulded or stamped on the pad you are replacing. If the number is worn away, send us a photo with dimensions and your rig model and serial — we will confirm which pad you need before you pay.

Both numbers are covered on our Sliding Pieces & Wear Pads category page, with a machine-to-part compatibility matrix.

Wear Signs Worth Acting On

The inspection routine is the same as for any feed beam pad, and it takes about five minutes per shift:

  • Thickness below the wear limit — check against the manual or against a new pad; a fingernail-catch step across the face means uneven wear has started.
  • Shiny metal contact marks on the rail — the clearest signal that the pad has stopped separating steel from steel. Stop and replace.
  • Cracks, chips or embedded rock dust — embedded grit turns the pad into sandpaper for the rail.
  • Uneven wear at one end — points to rail misalignment; new pads alone will not fix it.
  • Rising feed pressure or slower penetration — increasing friction in the sliding interface often shows up here first.
  • Collaring drift — play in the sliding interface appears first as inaccurate hole starts.

Choosing a Replacement Pad

For an aftermarket 3128303930, compare suppliers on the same points we use ourselves:

  • Fitment validation — dimensions cross-checked against the fitment list and real beams, not just a number match.
  • Polymer grade — a named material with stable dimensions under heat, load and hydraulic oil exposure.
  • Thickness tolerance — clearance in the feed system lives in fractions of a millimetre.
  • Flatness and surface finish — the running face decides how the rail wears.
  • Batch consistency — the tenth set should feel identical to the first.

A pad that is slightly thin or slightly off in profile will fit loosely, wear quickly and pass the blame to your rails. If a supplier cannot state the material grade or the tolerance, that tells you enough.

Stocking Strategy for a Mixed Fleet

Because 3128303930 spans several rig types, it is the natural first item in a wear-pad stock position:

  1. Count the consumers. Every rig on the fitment list that runs 3128303930 pads, times pads per beam, gives your consumption base.
  2. Set a min-max. Track average pad life per machine class, then hold a minimum that covers one full change-out on your most pad-hungry rig plus a safety margin for delivery time.
  3. Reorder on consumption, not on failure. Pads removed at the wear limit during planned maintenance cost nothing extra; pads that fail mid-shift cost downtime.
  4. Keep one spare set per beam position on the shelf, and let the supplier hold the rest — with a ex-stock dispatch partner, shelf space beats inventory.

Installation Notes

  • Clean the rail and carrier seats before fitting; grit trapped under a new pad becomes immediate rail wear.
  • Check fastener torque to the manual specification — an undertorqued pad moves, an overtightened one creeps.
  • Confirm the carrier slides freely by hand through a full stroke before returning the rig to service.
  • Re-check after the first shift: early seating wear is normal, movement is not.

Ordering Checklist

  1. The number on the worn pad (or a photo with dimensions if it is illegible).
  2. Rig model and serial number.
  3. Quantity.
  4. Delivery country and port, for an accurate shipped quote.

Send these four items to dimailmachinery@126.com and you will have a quotation within 12 working hours; stock items are dispatched promptly after order confirmation.

Frequently Asked Questions

Is 3128303930 really the same pad on a Boltec™ and a Roc™ D65?

Yes — the feed beam interface those machines share uses the same pad. Beam revisions can still vary, so the number on the old part and the serial number remain the deciding check before any order.

Can I use 3128307488 instead if 3128303930 is out of stock?

No. The two pads differ in dimensions. Substituting one for the other produces loose fit, fast wear and rail damage. Order the number on the pad you removed.

How long should a sliding piece last?

It depends on rock abrasiveness, feed force and hours. Pads are consumables measured in weeks or months of operation, which is exactly why they belong on planned maintenance intervals rather than run-to-failure.

Do you supply other wear parts for the same machines?

Yes. We supply a range of aftermarket parts for use with EPIROC® and Atlas Copco® equipment, and we quote full wear-parts lists as a single shipment. Send the list and we will mark what we stock.

Sourcing 3128303930

Dimail supplies the 3128303930 sliding piece as an aftermarket spare part for use with EPIROC® drill rigs — MOQ one piece, dispatched from stock, quoted within 12 working hours. Full details, photos and the inquiry form are on the 3128303930 product page; the parts catalog lists all part numbers we currently cover.

EPIROC®, ATLAS COPCO®, Boomer™, Boltec™, Roc™ and FlexiROC™ are trademarks of Epiroc AB and Atlas Copco AB. Dimail is not affiliated with or endorsed by either company; part numbers are used for cross-reference only.

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *